Spark Logic

24C32 EEPROM (24LC32A) connection guide

24C32 EEPROM (24LC32A) SOIJ-8 wiring guide with power, signal assignments, and bench checks.

PDIP-8 8 contacts
SOIC-8 8 contacts

SOIJ-8

8 contacts Current package
MSOP-8 8 contacts
TSSOP-8 8 contacts
X-rotated TSSOP-8 8 contacts
DFN-8 9 contacts
TDFN-8 9 contacts
SOT-23-5 5 contacts

Microchip Technology · Medium body · 1.27 mm lead pitch · Microchip package code /SM

Power and bypass

Required

Connect the EEPROM and a 3.3 V I²C host to a regulated 3.3 V rail with a shared ground. Fit a 100 nF ceramic capacitor directly across the EEPROM supply pins. Finish the signal connections before applying power.

C1 100 nF ceramic between 3.3 V and Ground3.3 VC1 100 nF ceramicGround

Bench checks

  • Measure about 3.3 V from VCC to VSS at the package.

Microchip DS20001713P · §1 and §2. Microchip AN1028 · Figure 1.

Connection scenarios

Read and write over I²C

With power off, tie WP to ground. Use a scratch address in the allowed range before testing writes on an installed device.

Fit C1 as shown in Power and bypass. Connect both open-drain host lines and start at 100 kHz. Tie A0, A1 and A2 to ground for this example.

The 7-bit client address is 0x50 + 4×A2 + 2×A1 + A0. Strap each pin to VSS or VCC before power-up.

Send two memory-address bytes, high byte first. The usable offset ends at 0x0FFF.

I²C wiring with separate pull-ups on SDA and SCL and WP tied low3.3 VR14.7 kΩR24.7 kΩSDASCLHostEEPROMVCCVSSWPCommon groundA0–A2

Bench checks

  • For a short bus, use R1 and R2 of 4.7 kΩ each and count any host-board pull-ups in parallel. At 100 pF the estimated 30–70% rise time is 0.40 µs and LOW current is about 0.62 mA at 0.4 V. Measure SDA and SCL rise time against the 1 µs Standard-mode limit before changing speed or adding wiring.
  • Read a selected byte by sending the client address with write direction, then the memory address, then a repeated START and the client address with read direction. End a one-byte read with NACK and STOP.
  • Send STOP to start programming, then use acknowledge polling with a bounded timeout. The maximum specified cycle is 5 ms. Read back the scratch byte to verify the write.
  • Split page writes at every 32-byte boundary. A write that crosses a boundary wraps inside the current page.

Microchip DS20001713P · §§5–8. Microchip AN1028 · Figure 1 and pull-up calculation.

SOIJ-8 wiring map

Highlighted contacts are used in the required step or selected circuit. Select a contact to inspect it.

Top view · Locate pin 1 using the package index mark.
Selected pin details

2 · A1

Input · Address

Chip select bit 1. Strap to VSS for 0 or to VCC for 1.

DS20001713P · §2 and Table 2-1

Electrical limits · Pin in the reference

Models and documents

This reference covers the standard package codes listed for Microchip 24LC32A and the 24LC32AX pin assignment in the linked datasheet. Match the full manufacturer part number before wiring a device marked 24C32. Use its own datasheet for other manufacturers or the Microchip AA and FC versions.

24LC32A
The /SM package suffix selects this outline. Check the ordering table for supported temperature and reel combinations.