ATtiny88 pinout

Package pin assignments for ATtiny88, with peripheral signals, clock grades and a serial programming guide.

QFN-28 29 contacts

PDIP-28 28 contacts

TQFP-32

32 contacts Current package

UFBGA-32 32 contacts

QFN-32 33 contacts

Microchip Technology · 32 numbered contacts. See the individual package drawings for footprint dimensions.

8 KiB flash · 512 B SRAM · 64 B EEPROM · 1.8–5.5 V · 12 MHz maximum · -40 to +85 °C

TQFP-32 pinout

TQFP-32

Top view · Pin 1 at the upper left · Schematic outline Scroll the map to reach all contacts.

Selected pin details

22 · PA1

Bidirectional · GPIO

General-purpose digital I/O. Alternate assignments: ADC7 (ADC), PCINT25 (EXINT).

After reset · GPIO driver is high impedance during reset. Clock, debug, and alternate-function use depend on fuse and peripheral configuration.

8008H · Pinout and peripheral signal descriptions

Electrical limits · Link to this pin

All 32 pins

Pin	Signal	Direction	Function
1	PD3 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT19 (EXINT), INT1 (EXINT).
2	PD4 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT20 (EXINT), T (TC0).
3	PA2 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT26 (EXINT).
4	VCC Supply	Supply	Digital supply. Connect every VCC pin and place a local 100 nF ceramic bypass close to each VCC-to-ground pair.
5	GND Return	Return	Supply return. Connect every ground pin.
6	PA3 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT27 (EXINT).
7	PB6 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT6 (EXINT).
8	PB7 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT7 (EXINT).
9	PD5 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: T (TC1), PCINT21 (EXINT).
10	PD6 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: AIN0 (AC), PCINT22 (EXINT).
11	PD7 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: AIN1 (AC), PCINT23 (EXINT).
12	PB0 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: ICP (TC1), PCINT0 (EXINT).
13	PB1 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: OCA (TC1), PCINT1 (EXINT).
14	PB2 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: SS (SPI), PCINT2 (EXINT).
15	PB3 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: OCB (TC1), MOSI (SPI), PCINT3 (EXINT).
16	PB4 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: MISO (SPI), PCINT4 (EXINT).
17	PB5 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: SCK (SPI), PCINT5 (EXINT).
18	AVCC Supply	Supply	Analog supply. Connect it to the supply even if analog conversion is unused. Follow the data sheet’s filtering guidance for precision conversion.
19	PA0 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: ADC6 (ADC), PCINT24 (EXINT).
20	PC7 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT15 (EXINT).
21	GND Return	Return	Supply return. Connect every ground pin.
22	PA1 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: ADC7 (ADC), PCINT25 (EXINT).
23	PC0 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: ADC0 (ADC), PCINT8 (EXINT).
24	PC1 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: ADC1 (ADC), PCINT9 (EXINT).
25	PC2 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: ADC2 (ADC), PCINT10 (EXINT).
26	PC3 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: ADC3 (ADC), PCINT11 (EXINT).
27	PC4 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: SDA (TWI), ADC4 (ADC), PCINT12 (EXINT).
28	PC5 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: SCL (TWI), ADC5 (ADC), PCINT13 (EXINT).
29	PC6 Input / I/O	Input / I/O	Active-low reset input by default. Use as GPIO only where the reset-disable fuse is supported and configured. Alternate assignments: PCINT14 (EXINT).
30	PD0 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT16 (EXINT).
31	PD1 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT17 (EXINT).
32	PD2 Bidirectional	Bidirectional	General-purpose digital I/O. Alternate assignments: PCINT18 (EXINT), INT0 (EXINT).

Signal assignments

Timer/Counter 1

Review each signal assignment and the peripheral enable conditions in the data sheet. T → PD5 · ICP → PB0 · OCA → PB1 · OCB → PB3

Analog comparator

Review each signal assignment and the peripheral enable conditions in the data sheet. AIN0 → PD6 · AIN1 → PD7

SPI peripheral

Use SCK, MOSI, MISO and a chip-select line. Firmware selects direction and clock phase. Check the separate ISP mapping when programming. SCK → PB5 · MISO → PB4 · MOSI → PB3 · SS → PB2

TWI / I²C

Connect SDA and SCL to the bus with pull-ups to a voltage supported by all devices. Verify the pull-up value for the bus capacitance and rate. SCL → PC5 · SDA → PC4

Analog-to-digital converter

Select the analog channel and reference in firmware. The reference choice and supply constrain the input range. ADC0 → PC0 · ADC1 → PC1 · ADC2 → PC2 · ADC3 → PC3 · ADC4 → PC4 · ADC5 → PC5 · ADC6 → PA0 · ADC7 → PA1

External interrupts

Review each signal assignment and the peripheral enable conditions in the data sheet. PCINT0 → PB0 · PCINT1 → PB1 · PCINT2 → PB2 · PCINT3 → PB3 · PCINT4 → PB4 · PCINT5 → PB5 · PCINT6 → PB6 · PCINT7 → PB7 · PCINT8 → PC0 · PCINT9 → PC1 · PCINT10 → PC2 · PCINT11 → PC3 · PCINT12 → PC4 · PCINT13 → PC5 · PCINT14 → PC6 · PCINT15 → PC7 · PCINT16 → PD0 · PCINT17 → PD1 · PCINT18 → PD2 · PCINT19 → PD3 · PCINT20 → PD4 · PCINT21 → PD5 · PCINT22 → PD6 · PCINT23 → PD7 · PCINT24 → PA0 · PCINT25 → PA1 · PCINT26 → PA2 · PCINT27 → PA3 · INT0 → PD2 · INT1 → PD3

Timer/Counter 0

Review each signal assignment and the peripheral enable conditions in the data sheet. T → PD4

PD4 (2)

Electrical limits

Parameter	Limit	Conditions and source
Supply and clock grade1.8–5.5 V · 12 MHz maximum	1.8–5.5 V · 12 MHz maximum	Up to 4 MHz at 1.8 V, 8 MHz at 2.7 V and 12 MHz at 4.5 V. 8008H · Speed grades and ordering information
Ambient temperature grade-40 to +85 °C	-40 to +85 °C	For this order code. Verify silicon revision and errata in the current manufacturer documentation. 8008H · Ordering information
Program flash8 KiB	8 KiB	Nonvolatile program memory. 8008H · Memory
SRAM512 B	512 B	Volatile data and stack storage. 8008H · Memory
EEPROM64 B	64 B	Nonvolatile data storage. 8008H · Memory
Clock and supplyOrder-code dependent	Order-code dependent	Use the grade table and the device’s speed-versus-voltage curve. 8008H · Electrical Characteristics

Models and documents

Each package lists the documented order codes and variants covered by this map. Select the marked model to see its peripheral assignments and memory. Check the exact order code and datasheet revision before laying out a PCB.

ATtiny88: 8 KiB flash · 512 B SRAM · 64 B EEPROM. Choose the marked order code for voltage, clock, and temperature.
ATtiny88-AU: 8 KiB flash · 512 B SRAM · 64 B EEPROM · 1.8–5.5 V · 12 MHz maximum · -40 to +85 °C
ATtiny88-AUR: 8 KiB flash · 512 B SRAM · 64 B EEPROM · 1.8–5.5 V · 12 MHz maximum · -40 to +85 °C

ATtiny88 data sheet· 8008H · Pin configuration, electrical characteristics, ordering table and serial programming.
ATtiny_DFP Device Family Pack· Machine-readable device definition: package contacts, peripheral routes, and memory sizes.
AVR Microcontroller Hardware Design Considerations· Power supply, reset network, and programmer connection guidance.
ATtiny88 documentation and errata· Check current manufacturer documentation, ordering status and silicon revision applicability.
AVR source register· Source identifiers, applicability, retrieval dates, and SHA-256 digests.