Spark Logic

GD32F103 connection guide

GD32F103 (LQFP64) connection guide. Power and boot from Flash. Connect a Serial Wire Debug probe.

PackageContactsDetails
LQFP48 48 GD32F103Cx · 48 leads
LQFP64 64 GD32F103Rx · 64 leads
LQFP100 100 GD32F103Vx · 100 leads

GigaDevice

Device variants · LQFP64

DeviceFlashSRAMSerial peripherals
GD32F103R4T6 16 KiB 6 KiB 2 USART, 1 SPI, 1 I²C, 1 CAN, 1 USBD
GD32F103R6T6 32 KiB 10 KiB 2 USART, 1 SPI, 1 I²C, 1 CAN, 1 USBD
GD32F103R8T6 64 KiB 20 KiB 3 USART, 2 SPI, 2 I²C, 1 CAN, 1 USBD
GD32F103RBT6 128 KiB 20 KiB 3 USART, 2 SPI, 2 I²C, 1 CAN, 1 USBD
GD32F103RCT6 256 KiB 48 KiB 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO
GD32F103RDT6 384 KiB 64 KiB 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO
GD32F103RET6 512 KiB 64 KiB 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO
GD32F103RFT6 768 KiB 96 KiB 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO
GD32F103RGT6 1024 KiB 96 KiB 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO
GD32F103RIT6 2048 KiB 96 KiB 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO
GD32F103RKT6 3072 KiB 96 KiB 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO

Power and boot from Flash

Required

Use a regulated 3.3 V supply and a single ground plane. Feed VBAT from the same rail for this single-supply setup. Fit each bypass capacitor close to its corresponding contacts. Pull BOOT0 low with 10 kΩ.

  • +3.3 V digital
    • Bench supply positive
  • Digital return
    • Bench supply return
  • +3.3 V analog
    • Same +3.3 V source
  • Analog return
    • Same ground plane
  • Backup supply
    • Same +3.3 V source
  • Boot strap
    • →
4.7 µF bulk between +3.3 V digital and Digital return+3.3 V digital4.7 µF bulkDigital return
100 nF × 4, one at each VDD lead between +3.3 V digital and Digital return+3.3 V digital100 nF × 4, one at each VDD leadDigital return
1 µF in parallel with 10 nF at VDDA between +3.3 V analog and Analog return+3.3 V analog1 µF in parallel with 10 nF at VDDAAnalog return
100 nF between Backup supply and Digital returnBackup supply100 nFDigital return
10 kΩ between Boot strap and Digital returnBoot strap10 kΩDigital return

Bench checks

  • Verify continuity from every supply and ground lead to its intended rail before powering up.
  • Confirm that the digital and analog rails are near 3.3 V and that BOOT0 remains low through reset.

GD32F103xx datasheet Rev. 3.3, §3.3 and Fig. 4-1. The 10 kΩ strap is a bench choice.

Connection scenarios

LQFP64 wiring map

External wiring example · Power and boot from Flash

Highlighted contacts are used in this circuit. Select a contact to highlight its wiring nets.

LQFP64

31 · VSS_1 · Bottom side, contact 15 from the left

Face the package marking. Pin 1 is beside the corner mark. Numbers advance counterclockwise.
Selected pin details

31 · VSS_1

Return · Ground

Digital ground. Connect every VSS lead to the ground plane.

Wiring requirements

GD32F103xx datasheet Rev. 3.3, Table 2-7

Connected nets

Electrical limits · Pin in the reference

Dashed lines show external connections in this wiring example.

  • Digital return
    • Bench supply return
    • Via 4.7 µF bulk to +3.3 V digital · Bench supply positive, VDD_4 (19), VDD_1 (32), VDD_2 (48), VDD_3 (64)
    • Via 100 nF × 4, one at each VDD lead to +3.3 V digital · Bench supply positive, VDD_4 (19), VDD_1 (32), VDD_2 (48), VDD_3 (64)
    • Via 100 nF to Backup supply · Same +3.3 V source, VBAT (1)
    • Via 10 kΩ to Boot strap · BOOT0 (60)

Manufacturer documents

Interactive maps cover LQFP48, LQFP64 and LQFP100. See Figures 2-3 and 2-7 of the datasheet for LQFP144 and QFN36. Match the suffix on the chip. Board headers and regulator connections depend on the PCB.