GD32F103 connection guide
GD32F103 (LQFP64) connection guide. Power and boot from Flash. Connect a Serial Wire Debug probe.
Device variants · LQFP64
| Device | Flash | SRAM | Serial peripherals |
|---|---|---|---|
| GD32F103R4T6 | 16 KiB | 6 KiB | 2 USART, 1 SPI, 1 I²C, 1 CAN, 1 USBD |
| GD32F103R6T6 | 32 KiB | 10 KiB | 2 USART, 1 SPI, 1 I²C, 1 CAN, 1 USBD |
| GD32F103R8T6 | 64 KiB | 20 KiB | 3 USART, 2 SPI, 2 I²C, 1 CAN, 1 USBD |
| GD32F103RBT6 | 128 KiB | 20 KiB | 3 USART, 2 SPI, 2 I²C, 1 CAN, 1 USBD |
| GD32F103RCT6 | 256 KiB | 48 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RDT6 | 384 KiB | 64 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RET6 | 512 KiB | 64 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RFT6 | 768 KiB | 96 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RGT6 | 1024 KiB | 96 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RIT6 | 2048 KiB | 96 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RKT6 | 3072 KiB | 96 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
Power and boot from Flash
RequiredUse a regulated 3.3 V supply and a single ground plane. Feed VBAT from the same rail for this single-supply setup. Fit each bypass capacitor close to its corresponding contacts. Pull BOOT0 low with 10 kΩ.
- +3.3 V digital
- Bench supply positive
- Digital return
- Bench supply return
- +3.3 V analog
- Same +3.3 V source
- Analog return
- Same ground plane
- Backup supply
- Same +3.3 V source
- Boot strap
- →
Bench checks
- Verify continuity from every supply and ground lead to its intended rail before powering up.
- Confirm that the digital and analog rails are near 3.3 V and that BOOT0 remains low through reset.
GD32F103xx datasheet Rev. 3.3, §3.3 and Fig. 4-1. The 10 kΩ strap is a bench choice.
Connection scenarios
LQFP64 wiring map
13 · VDDA
Analog supply for the ADC, clock and reset circuitry. Feed it from the VDD supply and bypass it to VSSA.
Wiring requirements
Required. Connect every VDD and VSS lead and both analog supply leads, even without ADC. Use 2.6–3.6 V and connect VSSA to the VSS ground. Keep VDD and VDDA within 300 mV during startup and operation.
Recommended. Feed VDD and VDDA from the same source.
Recommended. Place 1 µF and 10 nF in parallel close to VDDA and VSSA.
ADC or DAC reference. This package connects the reference internally to VDDA and VSSA.
- +3.3 V analog
- Same +3.3 V source
- Via 1 µF in parallel with 10 nF at VDDA to Analog return · Same ground plane, VSSA (12)
Manufacturer documents
Interactive maps cover LQFP48, LQFP64 and LQFP100. See Figures 2-3 and 2-7 of the datasheet for LQFP144 and QFN36. Match the suffix on the chip. Board headers and regulator connections depend on the PCB.
- GD32F103xx datasheet Rev. 3.3· Figures 2-4 to 2-6, pin tables 2-6 to 2-8, Figure 4-1 and ordering information.
- GD32F10x user manual Rev. 2.9· Boot modes, GPIO alternate functions and serial-wire debug.
- Source register· Document applicability, revisions and SHA-256 checksums.
