GD32F103 connection guide
GD32F103 (LQFP64) connection guide. Power and boot from Flash. Connect a Serial Wire Debug probe.
Device variants · LQFP64
| Device | Flash | SRAM | Serial peripherals |
|---|---|---|---|
| GD32F103R4T6 | 16 KiB | 6 KiB | 2 USART, 1 SPI, 1 I²C, 1 CAN, 1 USBD |
| GD32F103R6T6 | 32 KiB | 10 KiB | 2 USART, 1 SPI, 1 I²C, 1 CAN, 1 USBD |
| GD32F103R8T6 | 64 KiB | 20 KiB | 3 USART, 2 SPI, 2 I²C, 1 CAN, 1 USBD |
| GD32F103RBT6 | 128 KiB | 20 KiB | 3 USART, 2 SPI, 2 I²C, 1 CAN, 1 USBD |
| GD32F103RCT6 | 256 KiB | 48 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RDT6 | 384 KiB | 64 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RET6 | 512 KiB | 64 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RFT6 | 768 KiB | 96 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RGT6 | 1024 KiB | 96 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RIT6 | 2048 KiB | 96 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
| GD32F103RKT6 | 3072 KiB | 96 KiB | 3 USART, 2 UART, 3 SPI, 2 I²C, 1 CAN, 1 USBD, 1 SDIO |
Power and boot from Flash
RequiredUse a regulated 3.3 V supply and a single ground plane. Feed VBAT from the same rail for this single-supply setup. Fit each bypass capacitor close to its corresponding contacts. Pull BOOT0 low with 10 kΩ.
- +3.3 V digital
- Bench supply positive
- Digital return
- Bench supply return
- +3.3 V analog
- Same +3.3 V source
- Analog return
- Same ground plane
- Backup supply
- Same +3.3 V source
- Boot strap
- →
Bench checks
- Verify continuity from every supply and ground lead to its intended rail before powering up.
- Confirm that the digital and analog rails are near 3.3 V and that BOOT0 remains low through reset.
GD32F103xx datasheet Rev. 3.3, §3.3 and Fig. 4-1. The 10 kΩ strap is a bench choice.
Connection scenarios
LQFP64 wiring map
64 · VDD_3
Digital supply. Connect every VDD lead and place a local 100 nF bypass at each supply pair.
Wiring requirements
Required. Connect every VDD and VSS lead and both analog supply leads, even without ADC. Use 2.6–3.6 V and connect VSSA to the VSS ground. Keep VDD and VDDA within 300 mV during startup and operation.
Recommended. Feed VDD and VDDA from the same source.
Recommended. Place 100 nF at this VDD/VSS pair with short traces. Add 4.7 µF bulk capacitance to the digital rail.
Dashed lines show external connections in this wiring example.
- +3.3 V digital
- Bench supply positive
- Via 4.7 µF bulk to Digital return · Bench supply return, VSS_4 (18), VSS_1 (31), VSS_2 (47), VSS_3 (63)
- Via 100 nF × 4, one at each VDD lead to Digital return · Bench supply return, VSS_4 (18), VSS_1 (31), VSS_2 (47), VSS_3 (63)
Manufacturer documents
Interactive maps cover LQFP48, LQFP64 and LQFP100. See Figures 2-3 and 2-7 of the datasheet for LQFP144 and QFN36. Match the suffix on the chip. Board headers and regulator connections depend on the PCB.
- GD32F103xx datasheet Rev. 3.3· Figures 2-4 to 2-6, pin tables 2-6 to 2-8, Figure 4-1 and ordering information.
- GD32F10x user manual Rev. 2.9· Boot modes, GPIO alternate functions and serial-wire debug.
- Source register· Document applicability, revisions and SHA-256 checksums.
