Spark Logic

Microcontrollers and processors

STM8

Discussions and practical resources mentioning STM8.

Discussions 11

  1. Anyone tried to make a 3D Printer controller?

    ag123

    …ace with 3.3v devices (STM probably considered or even have products interfacing with STM8 / STM32 mcu which pretty much runs at 3.3v) and it seemed pretty advanced http://www.st.com/en/motor-drivers/l6470.html http://www.st.com/content/ccc/resource/ … 255075.…
  2. Black Magic Probe on an stm32f103c8

    RogerClark

    …to flash using another STLink. So I would keep your STlink to program other STM32 and STM8 boards Re:Blue Pill etc This is the name someone coined for the cheap generic STM32F103C8 boards that are easily available on eBay. They are a bit like an Arduino Nano, …
  3. Counterfeit F103s

    dannyf

    …on some stm parts has been around for a long time. I tried that on STM32F030 and then STM8 back in 2014. the same can be said about usb capabilities as well – you may see some non-USB capable (per datasheet) STM8s used in USB applications natively. or UID on p…
  4. DIY ST-Link SWIM programmer for STM8S?

    urielka

    I just made a guide (from zero to blinky STM8) based on this post and the original russian blog – http://www.stm32duino.com/viewtopic.php?f=35&t=1233 Including a minimal schematic (without leds) of the programmer board with STM32F103C8 minimum development …
  5. DOA boards

    zoomx

    … with broken reset button and a nasty STLink clone that works with STM32 but not with STM8. I suspected that something was wrong with wires until I got another STLink (Baite) that works with STM8. Some of UNO clones has regulator that doesn’t allow the same 5V…
  6. NUCLEO_073RZ support

    fpiSTM

    …for 64 bits it’s just a form factor Nucleo 144 is not 144 bits . STM32 are 32bits and STM8 are 8 bits. STLink are connected on PA3/PA2 (Rx/Tx). PeripheralPins.c show those pins can used 2 U(S)ART: https://github.com/stm32duino/Arduino_T … ins.c#L145 PinMap_UAR…
  7. ST-Link и Jlink

    til

    …32F103 (Blue Pill). ### Main differences - **ST-LINK** — designed primarily for STM32/STM8, inexpensive, and works well with STM32CubeIDE. - **J-Link (SEGGER)** — supports a wider range of ARM microcontrollers, offers advanced debugging features, SEGGER RTT, a…
  8. STM32F405 Based Radio Hacked

    RogerClark

    Thanks Michael I noticed that article as well. I find the STM32 and also the STM8 are quite widely used in Chinese made electronics. Its handy that some people have time to reverse engineer these devices, and IMHO it will lead to more sales of these devices fo…
  9. Uncle Andrew.. how come we have a $2 multi MHz board?…

    MarkB

    …al to a bluetooth connected microcontroller running a Forth environment (eForth on an STM8 or Mecrisp-Stellaris on an STM32). In essence it gives me an interactive and remotely programmable microcontroller. There are similar apps available on the Android App S…
  10. eBay digital voltmeter modification

    RogerClark

    …er electrical isolation. I also thought the meter I bought from eBay would contain an STM8 not an unknown chip. Just to complicate things, the laser operates in PWM at 20kHz to control its power. Im not even sure how accurate a moving coil meter is when given …
  11. from stm32 to stm8s

    ag123

    i’d less likely use stm8s as ‘standalone’ mcus, even though they could do that. the main reason is that with 8k flash and 1k ram http://www.st.com/content/st_com/en/pro … 103f3.html it would be quite a challenge to do partially what we are doing on stm32 howev…