Spark Logic

Displays, touch panels and LEDs

ILI9341

Discussions and practical resources mentioning ILI9341.

ILI9341 MSP3223 · 14-contact header Pinout

Discussions 38

  1. Porting Marlin to STM32.

    ag123

    …lement – hot bed) – 1 for mosfet fan (if we leave the fan on we could save this?) for ILI9341 LCD 7 pins SPI (/CS, CLK, MOSI, MISO) 4 pin C/D (command/data) 1 pin tft_reset 1 pin backlight 1 pin (optional) beeper 1 pin #define BEEPER_PIN 23 button switches &am…
  2. Recomendations for working components – TFT, OLED, ..

    68gt500

    …thout the above issues, but that looks horrible. :shock: Basically unusable. Does the ILI9341 library have the same shortcomings? Like i said, I have a Nextion on order, I will post my findings The frequency library that I have successfully used with my Uno is…
  3. SST26VF064B Library… help?

    rexnanet

    …tube.com/watch?v=Dui-L7S7nS0 https://www.youtube.com/watch?v=VOxv87-hZt8 The display (ILI9341) handles that well. Only at 80Mhz I couldn’t get it to work (using ESP8266) but I’m still going to try with shorter wires. I was testing with 20cm dupont wires, I hav…
  4. STM32F103C8 & TFT (ili9325)

    …un 21, 2016 1:24 pm Correction: Working library: https://github.com/iwalpola/Adafruit_ILI9341_8bit_STM/ JoaoLopes’s library supports ILI9341, and this one probably is an ILI9341. I checked the SPFD5408 datasheet, and Joao’s library definitely isn’t for SPFD540…
  5. USB Composite (HID / MIDI / Mass Storage) library

    RogerClark

    …ra, at 320 x 240 at around 11 FPS. I think the frame speed may be a limitation of the ILI9341, that we use to display the image. ( SteveStrong is the guru this) Unfortunately I have other more pressing commitments of my time, so I can’t help with this PS. I WI…
  6. USB Serial starts going slow if buffer on PC is not emptied

    victor_pv

    RogerClark wrote:Hi Guys, I was testing some code that writes to a ILI9341 display and also sends the same debug information to Serial. I left it doing a soak test and after about sending several thousand chars to the serial without the serial console being op…
  7. USB mass storage / SD card + speed

    heisan

    …hout DMA. You will see the difference, although it uses the same SPI functions as the ILI9341 lib, just that in 8 bit mode this time. I must do some more testing… But looking at it logically, 8 bit should not be a problem. SPI runs at most 1/2 CPU clock, so fo…
  8. Where to buy GD32F103

    Vassilis

    …PI working yet. SPI appears to be sending the correct data, but It didnt work with my ILI9341 display. However I could be doing something really stupid with the wiring rather than it being a real problem.
  9. [SOLVED] Adafruit_ILI9341_STM – hardware scrolling broken

    zoomx

    The SPI ILI9341 LCD that I have doesn’t work with Arduino at 5V (they are all white) but works with STM32 at 3.3V despite that they were announced as Arduino compatible. I never tested the SD card adapter but I believe that I have the resistor too.
  10. [SOLVED] FSMC LCD on STM32F407VET

    flyboy74

    …g shows on my screen. I have used and programmed a few different types of SPI screens(ili9341, st7735) using Python very successfully and these parallel screens have many of the same registers just use parallel instead of SPI. Can someone correct me if I am in…
  11. [SOLVED] ILI9341 STM32 Blue pill

    david.prentice

    Go on. I would guess you have a Red SPI ILI9341 3.3V display. With or without an XPT2046 touch controller. These boards must have the RST pin pulled high or under program control. Add a 10k pullup. Or connect the RST pin to a GPIO pin as nature intended. Note …
  12. [SOLVED] ILI9431 problem

    lapgoch

    …e SPI bus. I finally ditched the libraries <Adafruit_GFX_AS.h> and <Adafruit_ILI9341_STM.h> and just used <Adafruit_GFX.h> and <Adafruit_ILI9341.h> These worked perfectly , slow but fine for my application. So there seems to be a confli…
  13. [STM32GENERIC] F429i Discovery

    ChrisMicro

    For example, if that board really has ILI9341 on SPI, than the Adafruit ILI9341 just works That would be much too easy and I would have done an example long time ago. It is parallel ( p.34 ). Oh how I wish I had that board… In my opinion you should ask STM. Th…
  14. [libmaple] Black F407VET6

    stevestrong

    I just tested the graphicstest.ino from the attached ILI9341 lib on SPI1 of my black F4 board and it works with my repo. OK, some pixel groups are displayed wrongly in two of rectangle tests but the most important thing is that it does not hang. ILI9341 Test! …
  15. adafruit_ILI9341_STM for SPI2

    …ello, cause I needed the TFT on SPI2 I rewrote the library and renamed it to Adafruit_ILI9341_STM_SPI2 so it can easily coexist with the standard lib so if you need it you can run two independent ILI9341’s simultaneous. Better example would be to use with a an…
  16. by-passing the arduino-e-ness?

    mrburnette

    …t sure if that supply supported yet by Ivan (Arduino ESP8266), I wanted to hook up am ILI9341 but it looks the the previous examples didnt use he 12E’s SPI pins, it was just bit banging the GPIO (and I’m already using most of the ESP-12’s GPIO for LED’s and bu…
  17. some troubles with ili9341, spi connectivity issues?

    ag123Tue Apr 25, 2017 2:14 pmafter quite a bit of tests with the ili9341_stm library, i think i managed to get my rather ‘broken’ ili9341 lcds working. while trying out the graphics test the ili9341 i’m using is something like this http://www.ebay.com/itm/New-…
  18. which library can be use for TFT_320QVT

    dev

    …ten on tft pcb board. So, i think controller is ssd1289. So, it’s not worth to try to ILI9341 driver code. UTFT library is configured for 8080 or for 6800?