Spark Logic

Development and computing boards

Blue Pill

Discussions and practical resources mentioning Blue Pill.

Discussions 119

  1. DIY Oscilloscopes – List and Discussions

    …oid, Windows I just found this one, and it looks tasty! Simplistic hardware – STM32 “ BluePill ” module, bluetooth HC-06 module, OpAmp with programmable gain. DDS module optional. Android APK, an…
  2. DIY ST-Link SWIM programmer for STM8S?

    Kenjutsu

    … Russian site: http://bovs.org/post/107/programmator-o … m8-i-stm32. I used one of my Blue Pill boards and wired up only what is needed to get SWIM going for the STM8S, and using stm8flash (https://github.com/vdudouyt/stm8flash), I got my 4 STM8S board flashin…
  3. DLO-138 OScope

    dave j

    …s UI to be from that provided by DLO-138. I’ve also swapped the F103 for an F303 on a blue pill. Swapping it on a DSO-138 or even on a DSO-150, as I’ve thought, it’s no good because of the single analog channel. I’m thinking about making myself a pcb to get ev…
  4. DOA boards

    RogerClark

    …cturer (“Baite” store on Aliexpress) are the best bet, but are twice the price of the Blue Pill The Black Pill is also OK, and a bit cheaper than the Maple Mini Plenty of other larger boards are also OK (but more expensive) The “Ugly board” is another to avoid…
  5. Debugging Arduino sketch with STM32 Nucleo in Eclipse .. works !

    Vitalhb

    …t compiled a OLED sample project and started a debug session with Eclipse. I am using blue pill with St-Link V2 dongle. It worked just fine and I could even add ‘global’ expressions in Eclipse IDE. Just wanted to tell this if someone is trying so there’s no ne…
  6. Debugging using openocd with arm-none-eabi-gdb

    stevestrong

    …or consecutive steps. You say that it must be the refresh process of Eclipse? Hm, for blue pill it did not happen.
  7. Does "Baite" still make Maple Minis

    RogerClark

    BTW. I’ve tried emailing Vcc-gnd about the Blue Pill, but I don’t hold out much hope that they will get back to me. Baite dont seem to have updated their site either.
  8. Dual LFO with choice of waveforms using PT8211 and Blue Pill

    Archived excerpt Dual LFO with choice of waveforms using PT8211 and Blue Pill KenLaszlo Fri Nov 24, 2017 2:12 pm Hi folks Roger encouraged me to make a post here, so here’s me ‘…
  9. ENC28j60 fail

    zmemw16

    you posted a picture of the ‘Blue Pill” – not a network module. stephen
  10. Failed to reconnect serial monitor after uploading on macOS

    ag123

    …of course reduced a bit the sketch size but also broke the automatic board reset on a blue pill: since that addition I had to manually reset the board in order to complete the upload.. Removing the option restored the automatic board reset feature. Couldn’t te…
  11. Firmata

    RogerClark

    …STM official version, we added a WIP branch which adds support for the Maple mini and Blue Pill, but as it is not official there is not a Boards Manager for this either.
  12. First experience review of allpcb, $15 for 5 100x100mm boards, $5 for 50x50mm boards, shipped DHL

    victor_pv

    …– Wed Nov 29, 2017 2:19 am] – … I have a half complete, simple breakout board for the Blue Pill to connect to a ILI9341 and a OV7670 camera, so at $5 I may get my ass in gear and finish it and send off. As even if its useless its only $5 down the drain I had t…
  13. GD32F103RGT6 custom board

    …e to get STM32. I get all my STM32’s from China, but I normally only buy boards e.g. BluePill and rarely just STM32F103C8 MCU IC’s Cost of the BluePill is often cheaper than I can make a board,…
  14. Generator ON/OFF SOLVED

    …() { state ^= 1; // toggle state digitalWrite(PC13, (state ? HIGH : LOW)); // toggle bluepill led if ( state ) { pwmtimer3.resume(); } else { pwmtimer3.pause(); } delay(100); // let the pwm run…
  15. Getting started with STM32F407-VGT6 development board + Arduino IDE + Mac OSX

    mrburnette

    …e Mini clone was under $5 U.S.D. We made the jump. Maybe you need this power, but the Blue Pill boards are under $2 and we have vast amount of experience with it. I want new members who read your intro to know that I would suggest they have three (3) Blue Pill…
  16. HALMX :: MXBluePillF103C8 Roadmap

    …port. I pressed the upload button on arduino IDE and simultaneously I plugged in the bluepill to the usb port. With that trick the bluepill was programed successfully. I am thinking right now o…
  17. Hacking the GD32 based ‘Autool X50 OBD2 Monitor and diagnostic Display’

    ahull

    …----- // // STM32F103C8XX Pin numbers - chosen for ease of use on the "Red Pill" and "Blue Pill" board // Touch Panel Pins // T_CLK T_CS T_DIN T_DOUT T_IRQ // PB12 PB13 PB14 PB15 PA8 // Example wire colours Brown,Red,Orange,Yellow,Violet // -------- Brown,Red,…
  18. Help with st-link

    infrared

    …2 interface. I have been using a cheap st-link v2 dongle to program/debug stm32f103c8 blue pill boards, and CubeMX to generate the chip configuration and app framework. Last night, I upgraded my HAL libraries to STM32Cube_FW_F1_V1.4.0, migrated one of my proje…
  19. Help with st-link v2

    … guys. I’m a total beginner and I could really use your help with this. I just got a blue pill . And along with it I bought .. The full discussion was unavailable in the source capture.
  20. How to change the clock speed of STM32L476RG nucleo board?

    …ov 26, 2017 6:09 pm I didn’t understand! STM32F103 chips (Cortex M3, 72MHz one) like BluePill have got 2 wait states while reading from flash memory. It means they do not usually perform 1 inst…