Spark Logic

Development and computing boards

Nucleo

Discussions and practical resources mentioning Nucleo.

Discussions 47

  1. Install STM32duino on Raspbian?

    Rick Kimball

    …e stlink. The whole idea of putting a mass storage device as the upload method on the nucleo boards was to make it simple to use with no extra drivers required.
  2. Is anyone interested in helping to make an Arduino Due which uses [edited:] a 100-pin STM32L471

    devan

    On the topic of CMSIS-DAP, if you want the full mbed/Nucleo-style drag’n’drop functionality, that’s based on the DAPLINK project, which is open source (but requires Keil/IAR to build) and has been ported to the STM32F103. Off the top of my head, the DAPLink fi…
  3. NUCLEO_073RZ support

    fpiSTM

    Oh nucleo 64 is not for 64 bits it’s just a form factor Nucleo 144 is not 144 bits . STM32 are 32bits and STM8 are 8 bits. STLink are connected on PA3/PA2 (Rx/Tx). PeripheralPins.c show those pins can used 2 U(S)ART: https://github.com/stm32duino/Arduino_T … i…
  4. Need some guide for learning STM32s

    RogerClark

    … @edogaldo At the moment, your best hardware choice is the Maple Mini rather than the Nucleo STM have only just released the “core” for 2 of their Nucleo boards, and it has not been extensively tested, and hardly anyone on the forum actually has a Nucleo board…
  5. New wiki

    RogerClark

    …ers can add more detail if they have that specific board. e.g. I know @madias has the Nucleo F103RB (but no longer uses it as its a pain to use)
  6. Nucleo F401 branch on github sheepdoll

    Archived excerpt Nucleo F401 branch on github sheepdoll sheepdoll Wed Jun 03, 2015 7:33 pm Since I need to access it on a r…
  7. Nucleo-L476RG Audio Library support

    pareidolialjebus

    …wer you both, then settle down to start porting my existing midi software over to the nucleo board. But guess what? My chinese boards arrived. I ordered them on the 20th, the dispatch note said they would arrive in November, but both my programmer and board we…
  8. Porting Marlin to STM32.

    victor_pv

    …esn’t seem to need it, all the other ARM ports use M3 except the current port for the Nucleo, and that probably doesn’t use it much since Marlin doesn’t use much floating point calculations. I dont want to rewrite Marlin, only write the HAL part so it runs on …
  9. PrintF via SWO

    Slammer

    …th ST-Link directly (with breakpoints, step execution, etc) While SWO is working with Nucleo boards, this is not working with ST-Link V2 clones as the SWO does not exist.
  10. SD card SDIO

    sheepdoll

    … hardware/software SPI and the rest of the library. When I was playing about with the Nucleo and discovery example code, even this bridge code was included. All the puzzle pieces are here, They just have to be assembled in the right order.
  11. STM32-RFM69

    fpiSTM

    …) but I get this error while compiling: I assume you use the STM core and you use the Nucleo F401. PA3 is used for Serial RX (via STLINK) so avoid to use it for attach interrupt. By default your example (ino) set irqnum to 3. Even if it is a wrong name as it s…
  12. STM32F030F4P6 using Arduino IDE

    aryeduino

    … using STLink or Serial? The Maple mini uses the same communication as the Blue Pill? NUCLEO boards have an embedded ST-Link, so use STM’s core and stay happy, Yes I know BUT they are NOT Cheap will eventually try them as well… With non-official cores, just lo…
  13. STM32F091 ADC resolution 10 bit instead of 12 bit

    …bit instead of 12 bit GianniDPC Sat Jun 24, 2017 4:04 pm I just tested the ADC on my Nucleo STM32F091 board, and it shows a 10-bit resolution like the original Arduino’s but my board supports…
  14. STM32F103C8 & TFT (ili9325)

    … You only supplied .H and .INO I could then debug your Library with your sketch on my NUCLEO board. (I just need to edit the write8(), setWriteDir() … macros) David. mausi_mick Wed Nov 23, 2016 8:58 am Hi, it’s a problem, because serial.print etc doesn’t funct…
  15. STM32F303CC on Cheap Mini Dev Board: Support for SMT32F3

    RogerClark

    …ifferent way to Libmaple. I think STM also intend to bring out their own core for the Nucleo F3, but its a long way down their To Do list, so I dont think its likely to be released any time soon.
  16. STM32F405 Teensy derivative

    onehorse

    … was able to translate a few of my Teensiduino sketches and make use of the STM32F401 Nucleo board to read sensors and do simple sensor fusion. I started designing a Teensy-like STM32L4 with the intent of using it in the same way but was happily surprised to r…
  17. STM32L476RG

    GrumpyOldPizza

    …IO mode. I’ve changed the variant.cpp and variant.h looking the variant.cpp given for nucleo-dragonfly. However, not succeeded. Can you look at the codes given below, please? Should I do anything more? #include "FS.h" #include "stm32l4_wiring_private.h" void s…
  18. WFI issue (solved)

    RogerClark

    aro_72 wrote:Nucleo-L476 is a STM32 board, based on STM32L476RG (low power version, Cortex-M4)
  19. Where does the stm32L4 sit, in terms of support?

    GrumpyOldPizza

    …nting the minimum functionality required by Arduino. Upside is that pretty much every Nucleo board sort of works … The soul of the STM32L4 (and STM32L0 for that matter) is to have a ultra low power Arduino Core that offers USB CDC/HID/MSC, a robust FAT file sy…
  20. Yet another OSX Rant – Peculiar issue

    RogerClark

    …can’t do it via the boards manager at the moment as the BM install only works for the Nucleo) BTW. I do have a old Macbook Pro, but its slightly too old to allow me to install Sierra. I also have a Hackintosh, but its the same situation, too old for Sierra, an…