Spark Logic

Hardware catalog

Find component pinouts and wiring guides, or look up hardware in the Spark Logic discussion archive.

Results for “STM8”

Component references

No matching component references.

Community equipment

  • STM8
    Archived topics
    • DOA boards
      …with broken reset button and a nasty STLink clone that works with STM32 but not with STM8 . I suspected that something was wrong with wires until I got another STLink (Baite) that works with…
    • STM32F405 Based Radio Hacked
      …7:49 pm Thanks Michael I noticed that article as well. I find the STM32 and also the STM8 are quite widely used in Chinese made electronics. Its handy that some people have time to reverse …
    • NUCLEO_073RZ support
      …’s just a form factor ;)Wink Nucleo 144 is not 144 bits ;)Wink. STM32 are 32bits and STM8 are 8 bits. STLink are connected on PA3/PA2 (Rx/Tx). PeripheralPins.c show those pins can used 2 U(…
    • Counterfeit F103s
      …n some stm parts has been around for a long time. I tried that on STM32F030 and then STM8 back in 2014. the same can be said about usb capabilities as well – you may see some non-USB capabl…
    • DIY ST-Link SWIM programmer for STM8S?
      …mx Tue Mar 01, 2016 10:13 am The BMP has a complete emulation of a STlinkv2? Because STM8 uses SWIM instead STM32 uses SWD. STlinkv2 clones have two different ports, one SWIM and the other …
    • eBay digital voltmeter modification
      …, 2016 10:43 am Hi Guys I bought a voltmeter on eBay the other day thinking it had a STM8 , which I could reprogram (as its been hacked before and there is source code available to re purpos…
    • from stm32 to stm8s
      …e up to an ADC pin Smile martinayotte Sat May 06, 2017 9:16 pm I would not mess with stm8 , first simply because you need a different compiler, second, the resources are limited. For small t…
    • Uncle Andrew.. how come we have a $2 multi MHz board?…
      …l to a bluetooth connected microcontroller running a Forth environment (eForth on an STM8 or Mecrisp-Stellaris on an STM32). In essence it gives me an interactive and remotely programmable …
    • Anyone tried to make a 3D Printer controller?
      …ce with 3.3v devices (STM probably considered or even have products interfacing with STM8 / STM32 mcu which pretty much runs at 3.3v) and it seemed pretty advanced … 255075.pdf it sports co…
    • Black Magic Probe on an stm32f103c8
      …o flash using another STLink. So I would keep your STlink to program other STM32 and STM8 boards Re:Blue Pill etc This is the name someone coined for the cheap generic STM32F103C8 boards th…
  • STM8S
    Archived topics
    • Counterfeit F103s
      …id about usb capabilities as well – you may see some non-USB capable (per datasheet) STM8s used in USB applications natively. or UID on parts not specified for UID…. obviously, the risk of r…
    • DIY ST-Link SWIM programmer for STM8S?
      Spark Logic archive DIY ST-Link SWIM programmer for STM8S ? Kenjutsu Mon Feb 29, 2016 9:26 am Hello everyone, A while back I ordered a few “STM8S103F3P6 Minim…
    • from stm32 to stm8s
      Spark Logic archive from stm32 to stm8s ag123 Sat May 06, 2017 5:18 pm these $1 stm8s boards is tickling if i should mess with them Smile ……
  • STM8S003
    Archived topics
    • from stm32 to stm8s
      …f103 is a native usb device dannyf Wed May 31, 2017 10:05 pm I’m a big fan of STM8S. Stm8s003 being my goto 8bit chip now. Likely them for the small size, uniformity, easy availability and low …
  • STM8S103F3P6
    Archived topics
    • DIY ST-Link SWIM programmer for STM8S?
      …M8S? Kenjutsu Mon Feb 29, 2016 9:26 am Hello everyone, A while back I ordered a few “ STM8S103F3P6 Minimum System Development Board”s with a clone ST-Link programmer. The ST-Link programmer was DOA,…
  • Программатор SWIM для STM8S
    Archived topics
    • DIY ST-Link SWIM programmer for STM8S?
      Spark Logic archive DIY ST-Link SWIM programmer for STM8S? Kenjutsu Mon Feb 29, 2016 9:26 am Hello everyone, A while back I ordered a few “STM8S103…