Generic components and modules without part numbers
EEPROM
Discussions and practical resources mentioning EEPROM.
Discussions 23
- $10 O-Scope revisited
efftek
…eries from the USB. Ive also thought to put a link in to connect the CS to either the EEPROM or the SD card on the TFT shield – all usable pins were used so I cant have a CS for both. Once I have it made and I know I havent made a booboo, I’ll put the eagle fi…
- Anyone tried to make a 3D Printer controller?
xebbmw
…either. Other than that, is a nice board with all IO pins broken out, 32Khz xtal, i2c eeprom, sdcard. There is an F103VCT version, surprisingly for a couple of bucks more. But I really like the tiny form factor, and that can be unplugged for programming, testi…
- Arduino IDE
RogerClark
…D card slot on the back, but the other doesnt, and I’m not sure if they both have I2C EEPROM It amazes me why they bother to make 2 different PCBs. I could understand omitting the SD card and the EEPROM i.e have them on the PCB but not install them. I wouldnt …
- Blue pill reading Winbond 25Q80 SPI flash
Jimbo13
…rcs compiler.objcopy.cmd=arm-none-eabi-objcopy compiler.objcopy.eep.flags=-O ihex -j .eeprom --set-section-flags=.eeprom=alloc,load --no-change-warnings --change-section-lma .eeprom=0 compiler.elf2hex.flags=-O binary compiler.elf2hex.cmd=arm-none-eabi-objcopy …
- Counterfeit F103s
dannyf
the observation of more ram / eeprom than specified in the datasheet on some stm parts has been around for a long time. I tried that on STM32F030 and then STM8 back in 2014. the same can be said about usb capabilities as well – you may see some non-USB capable…
- DLO-138 OScope
tales von milet
…eneric_stm32f103c" "-IC:\Arduino1.8.3\hardware\Arduino_STM32-master\STM32F1\libraries\EEPROM" "-IC:\Users\Meiner\Documents\Arduino\libraries\Adafruit-GFX-Library-master" "C:\Users\Meiner\AppData\Local\Temp\arduino_build_317073\sketch\DLO-138.ino.cpp" -o "C:\Us…
- EEPROM emulator how to use on Maple Mini ?
Araneus
[z1rqdym – Thu Sep 17, 2015 7:06 pm] – The reason to use an eeprom is to save pid gains. İf i change these gains every time via programming the board this spend me a lot of time. İ need to configure 9 gain. Only today i change these values 50 times. And can no…
- Flashstorage made for Duo
victor_pv
RogerClark wrote: AFIK EEPROM is just a name given by the Arduino team, for code to allow you to write to the program Flash. In reality there is only Flash on most MCUs
- Hacking the GD32 based ‘Autool X50 OBD2 Monitor and diagnostic Display’
ahull
…appears to speak i2c with a 33KHz clock. The pinouts (SDA on 5 and SCL on 6) match an eeprom, but the VCC and GND pins are opposite, also the amount of data coming to/from is tiny. LIke 1 or at most 2 bytes per read/write. I’m not sure what it is. It might not…
- I2C issue with MLX90640
…ny reports… Member #1419220 / about 2 months ago / The MLX90640 I2C can only read the EEProm at <400K, otherwise you get errors or crazy values and parameter extraction failed. It also needs 80+ ms to power on before you can read it. The MLX90640 needs 1M o…
- Is anyone interested in helping to make an Arduino Due which uses [edited:] a 100-pin STM32L471
lkcl
…ter user interface a connector for the ESP8266 could be useful. ( BLE ? ) An external EEPROM or FLASH can be useful. http://esp8266.github.io/Arduino/versio … digital-io and a little more besides… all of which looks hellishly complicated for what should be a s…
- LSE RTC calibration
chinhduy
…e clones, poor quality was acceptable. DS3231 is a good solution for RTC and external EEPROM. No need to emulate the eeprom anymore.
- New wiki
RogerClark
…on , if it has one, or more, buttons, details of connected SD card or external RAM or EEPROM etc, and whether these external hardware items are supported (a lot of boards have SD but its connected via SDIO which we dont have a library for) The full technical s…
- Porting Marlin to STM32.
youprint
…y compiled Marlin on a f103re and on a f103ze. It seems to work. I had to disable the EEPROM emulation function and I modified a little bit the Hal spi hardware. Now I can connect to my stm32 via pronterface I’m preparing a test board now : Image I’m going to …
- RTC Libs.
RogerClark
…t needed to store some calibration data, which may fit in these registers. I know the EEPROM can be used as well, for that sort of storage, but its much harder to update, because you need to erase and re-write a page every time you want to change a byte. Where…
- USB Composite (HID / MIDI / Mass Storage) library
arpruss
…eading is just memcpy. Writing is here: https://github.com/rogerclarkmelbourne/ … ies/EEPROM
- [SOLVED] I2C2 on STM32F103C8T6 and HWire
…re В индексированной копии видна ветка от июня 2017 года. Автор luca_stm32 подключил EEPROM к PB10/PB11: программная реализация I2C работала, а HWire на I2C2 останавливал выполнение после выв…
- [libmaple] Black F407VET6
stevestrong
Not for this board, but maybe for the generic mini, there is an I2C EEprom on board. Only time is missing…
- adafruit_ILI9341_STM for SPI2
…on a specific SPI: Like: NRF and/or XPT2046 on SPI1 and the ILI9341, SD-Card, Winbond EEPROM’s on SPI2 For sure it would be better to use “high speed SPI devices” on SPI1, but I won’t rewrite the radiohead library (If somebody digged into the code of this lib,…
- by-passing the arduino-e-ness?
RogerClark
…which purely provides access to hardware functions that the core Arduino API doesnt. (EEPROM library is the same) But… I think in reality it would be impractical to write such a library to be compatible with Libmaole, as it would proably cause massive code blo…
